Flotation is the most effective method of removing contaminants such as fats, suspensions, and petroleum substances.
Flotation is the most effective method of removing contaminants such as fats, suspensions, oil-derived substances and other undissolved substances found in industrial wastewater. The separation of these contaminants takes place in chemical processes using coagulants and flocculants (polymers). After separation, separation takes place using a water-air mixture in the flotation chamber. The resulting sludge is discharged outside the system and possibly dewatered before being disposed of, e.g. in a biogas plant.
Mechanical separation, i.e. separating solid elements from the wastewater stream
Most industrial wastewater streams contain solids that must be removed before wastewater reaches the treatment plant equipment. Removal of solids is necessary to protect pumps, mixers, sensors and other system components from blocking or even damage. In EMI installations, we use two stages of mechanical pre-treatment: coarse and fine. Coarse pre-treatment removes the largest elements, with a cross-section above 20 mm, and is carried out at the inlet to the first pumping station, before wastewater comes into contact with any pump. Coarse separation devices include vertical screens, basket screens and step/hook screens. The purpose of fine mechanical pre-treatment is to further remove solids, with their cross-section dropping below 3 mm, most often to 1 mm, although in some cases it is appropriate to use even smaller cross-sections (up to 0.25 mm). At this stage, rundown and rotary screens are used. The latter type of screen is used in a system with external or internal inflow. Mechanical pre-treatment involves very low costs, mainly resulting from the consumption of water rinsing the screens. No reagents are used, and energy consumption is minimal. Mechanically pre-treated wastewater is suitable for further treatment by physico-chemical and biological means.
A wastewater treatment system that uses anaerobic microorganisms to decompose organic matter.
The UASB (Upflow Anaerobic Sludge Blanket) is a wastewater treatment system that uses anaerobic microorganisms to break down organic matter. Wastewater is introduced from the bottom of the reactor and flows upwards through a layer of biological sludge. The microorganisms in the sludge break down organic pollutants, producing biogas, mainly methane and carbon dioxide. This biogas rises to the top of the reactor, where it is collected and can be used as an energy source. The granular sludge acts as a natural filter, retaining solid particles and ensuring efficient wastewater treatment. The purified water leaves the reactor through the top, and part of the sludge is recirculated, which helps maintain high microbiological activity. The UASB is characterized by a simple design, low operating costs and the ability to effectively treat wastewater with a high organic content.
Advanced wastewater treatment system that combines anaerobic decomposition processes with efficient sludge separation.
The anaerobic biological reactor of full mixing with sludge separation in the gas flotation system is an advanced wastewater treatment system that combines anaerobic decomposition processes with effective sludge separation. In the reactor, the wastewater is intensively mixed, which ensures even contact with anaerobic microorganisms that decompose organic matter. During this process, biogas is produced, mainly methane and carbon dioxide. Biogas (or nitrogen) is then used for flotation, i.e. raising sludge to the surface thanks to gas bubbles. The raised sludge is easily collected from the surface of the flotation unit, which allows for its effective separation from the purified water. The purified water is discharged from the flotation unit, while the sludge is recirculated or removed, depending on the needs of the process. This system combines the advantages of intensive mixing and effective sludge separation, which ensures high treatment efficiency and operational stability. A great advantage is also the small amount of sludge produced in the process.
Advanced wastewater treatment system using anaerobic processes and membrane technology.
The anaerobic biological reactor of full mixing with sludge separation in the membrane ultrafiltration system is an advanced wastewater treatment system using anaerobic processes and membrane technology. In the reactor, the wastewater is intensively mixed, which ensures even contact with anaerobic microorganisms that decompose organic matter into biogas, mainly methane and carbon dioxide. After the biodegradation process, the mixture of wastewater and sludge flows through ultrafiltration membranes. These membranes act as filters that retain solid particles, microorganisms and sludge, allowing only purified water to pass through. The purified water is discharged from the system, while the sludge is concentrated and recirculated to the reactor, which allows maintaining high microbiological activity. Ultrafiltration ensures high quality of purified water and eliminates the need for additional sludge separation processes. Thanks to the combination of intensive mixing and advanced membrane technology, this system is very efficient, stable and suitable for the treatment of wastewater with a high content of organic substances.
A wastewater treatment system that uses biomass carriers immersed in a reactor filled with water.
The MBBR (Moving Bed Biofilm Reactor) is a wastewater treatment system that uses biomass carriers immersed in a reactor filled with water. Wastewater is introduced into the reactor, where the carriers, covered with a biofilm of microorganisms, move freely, providing a large surface area for the degradation of organic pollutants. The microorganisms on the carriers decompose the organic matter, which leads to the purification of the wastewater. The system is aerated to provide oxygen necessary for biological processes and to keep the carriers in constant motion. After purification, the water flows through a sieve separation system that retains the carriers in the reactor, and the purified water is discharged. MBBR is flexible and scalable, which allows for easy adaptation to changing conditions and wastewater loads. Due to its simplicity and efficiency, this system is widely used in various wastewater treatment applications.
Averaging to improve efficiency and reduce wastewater treatment costs.
Wastewater in industrial plants is generated in many places and in many processes. As a result, its quantity and composition fluctuate significantly during the day and sometimes many days. Adjusting the treatment process to rapidly changing wastewater would be inefficient and uneconomical. Therefore, in industrial installations we use equalization tanks of appropriate size and equipment. We select the size based on data from the plant, industry knowledge and our own experience. The equipment of equalization tanks may include pumps, mixers, aeration systems, neutralization systems, by-passes and additional interceptor tanks and many other elements carefully selected to meet the requirements of individual cases.
Technology from the group of advanced oxidation processes used in special cases.
The Fenton process is an advanced oxidation method used in industrial wastewater treatment that uses chemical reactions to degrade organic contaminants. The process involves the reaction of iron (II) with hydrogen peroxide (H₂O₂) to produce powerful hydroxyl radicals (•OH). These radicals are highly reactive and effectively oxidize a wide range of organic contaminants, converting them to less harmful products or completely mineralizing them. In the Fenton process, iron acts as a catalyst, accelerating the reaction and increasing the efficiency of the process. Once the reaction is complete, the byproducts are removed or processed further, and the purified water can be subjected to further treatment steps. The Fenton process is effective in removing difficult-to-decompose contaminants such as industrial chemicals, dyes, pesticides, and some toxic substances.
pH correction in flow or batch mode
Ensuring the appropriate pH value in sewage is very important for two reasons. Firstly, each receiver (sewage system, environment) requires that the sewage directed to it has a pH within a predetermined range. Secondly, the sewage pretreatment and purification processes themselves require ensuring their appropriate pH. Emi offers a wide range of solutions, from simple systems with one measurement and dosing of one neutralizing agent to complex, multi-stage systems requiring the use of specific neutralizing agents. pH correction can take place at many levels, stages and in one of two modes: flow (online) or batch.
EMI offers specialized containers with built-in equipment for the implementation of any industrial wastewater treatment processes.
EMI has developed modular container systems in a marine version and designed to be connected into larger systems. The containers we offer have been designed from the ground up to operate in the harsh conditions of industrial sewage treatment plants. The interiors are lined with 100% stainless steel, have heating, ventilation, health and safety devices and individually configured technological equipment. The use of container construction allows for the shortest possible project implementation time. The entire installation is prefabricated in the EMI production plant and is delivered ready for start-up immediately after connection on site (in some cases preparatory works are required, such as tanks and underground networks, ground hardening, etc.). EMI's offer also includes tanks in containers that can perform averaging, storage and even become biological reactors.